Article no: 0500 5000
From recording of the measured data, automatic sensor identification, indication on a big colour screen, alerting, storage up to remote read-out via webserver … this is all possible with DS 500. By means of the CS Soft software alarms can be sent via SMS or e-mail. On the big 7″ colour screen with touch panel all information are available at a glance. The operation is very easy.
Article no: 0500 3225
The measuring instrument DS 300 mobile enables the analysis of compressed air stations. 2 clamp-on ammeters measure the current consumption of every single compressor. Optionally also 2 pressure sensors, temperature sensors or any other analogue sensors can be connected.
Article no: 0500 3000
DS 300 multifunctional measuring instrument with 2 inputs for consumption and dew point sensors (without sensors) for all relevant parameters for compressed air
Series 160S Pitot Tubes are designed specifically for flow measurement of dirty, particulate laden air or gas streams typical in smoke stack and other environmental testing. Large 5/16″ dia. stainless steel tubing resists plugging under harsh, sooty conditions which quickly block conventional flow sensors. Total and static pressure tubes are precisely aligned and welded together every six inches for maximum accuracy, strength and long term durability. Versatile 1/8″ female NPT connections easily adapt to any type of pipe or tubing. A pair of 1/8″ NPT to 3/16″ I.D. tubing adapters is included plus a handy molded vinyl cap to protect tip when not in use. Supplied with complete instructions.
Ideal for use with our precision manometers and air velocity gauges, Dwyer® Pitot Tubes are constructed from corrosion resistant stainless steel for a lifetime of service. ASME design meets AMCA and ASHRAE specifications for maximum accuracy over a wide variety of flow conditions. No correction factors required as ASHRAE tip design yields a calibration factor of 1. ASHRAE design needs no calibration! Permanent, stamped insertion depth graduations on sides of 160 series facilitate accurate positioning. Static pressure port is parallel to sensing tube allowing quick, easy alignment of tube with air flow. Low sensitivity to misalignment gives accurate reading even when tube is misaligned up to 15 degrees. Various standard sizes are available for use in ducts as small as 4″ dia. or as large as 36 ft. dia. A universal model fits user supplied 3/4″ schedule 40 (standard) pipe in any length. Several convenient mounting options are available for permanent installations.
Article no: 0695 1
Intelligent solutions for accurate consumption measurement for compressed air and gases
Article no: 0695 0
Intelligent solutions for accurate consumption measurement for compressed air and gases.
Article no: 0695 0409
Flow direction switch for compressed air systems
The new thermal flow direction switch VA 409 with direction indication serves for determination of the flow direction of
compressed air and gases especially in closed circular pipelines.
Article no: 0695 4001
Consumption sensor for compressed air and gases
The new VA 400 for cunsumption measurement of compressed air and gases in a robust housing with and without dosüöay with actual consumption in m³/h and counter in m³.
Article no: 0695 0122
Consumption sensor VA 400 max. version (185 m/s) inclusive certificate and 5 m cable
Recommended for installation from 10 to 50 bar.
By means of a special drilling device a measuring site with 1/2″ ball valve can be easily set up within a few minutes. As an alternative to the welding of the 1/2” fitting also a spot drilling collar can be used.
Article no: 0601
DS 300 displays the actual value (m³/h, m³/min) and the total consumption. A 4…20 mA output for m³/h and a pulse output for m³ are available for routing to a superior building management system (PLC).
Article no: 0600 4005
DS 300 displays the actual value (m³/h, m³/min) and the total consumption. A 4…20 mA output for m³/h and a pulse output for m³ are available for routing to a superior building management system (PLC).
The large measuring range of the consumption sensors enable the recordings of high consumptions (e.g. on weekdays) and the determination of leakage of a few litres/min (e.g. weekends).
Article no: 0600 4005
DS 300 displays the actual value (m³/h, m³/min) and the total consumption. A 4…20 mA output for m³/h and a pulse output for m³ are available for routing to a superior building management system (PLC).
The large measuring range of the consumption sensors enable the recordings of high consumptions (e.g. on weekdays) and the determination of leakage of a few litres/min (e.g. weekends).
Article no: 0600 6000
The portable dew point meter DP 300 is the ideal instrument for service and is supplied in a convenient case.
Thanks to the internal rechargeable battery it measures quickly and reliably for a duration of up to 15 hours.
The set includes everything that you need for an uncomplicated dew point measurement.
